As an Amazon Associate I earn from qualifying purchases.
Kyuionty #ad - The input voltage range of the dc motor driver is dc 6. 5v-27v, dc 12v or 24v can be input, the rated output current of each port is 7A, and the total output power is 160W.
Forward & reverse rotation: in1, in2/iN3, IN4 ports can control the forward or reverse rotation of the motor. Pwm speed control: enable the signal terminal ENA input PWM to adjust the speed, PWM frequency range 0-10KHZ.
uniquegoods #ad - The switching frequency is high, the most up to 60KHZ, thus effectively avoiding the low frequency of commissioning motor brings unpleasant. Large heat sink at high currents can effectively drive module for cooling, maintain good and stable performance of the module.
3. 3v and 5v mcu can control this module, and only need the way the motor power 12V ~ 48V. The control interface is very simple: a1. A2 = 00 when the brakes; when a1.
Ardest #ad - Use large-capacity filter capacitors and diode with freewheeling protection function, increasing reliability. To avoid damage the voltage stabilizing chip, please use an external 5V logic supply when using more than 12V driving voltage.
Well built dual-channel H-bridge driver working mode creates higher working efficiency. L298n dual motor controller module is a neat motor control module based on the L298N H-bridge IC that can allows you to control the speed and direction of two DC motors, or control one bipolar stepper motor with ease.
KNACRO #ad - The use of optocoupler isolation of all control signals, static discharge circuit. Simulate l298 logic control, each channel support three-wire enable control, reversing and braking. Dual channel with rated 7a constant current output fit for driving 24V 115W/12V 40W or below DC motor.
Thincol #ad - The best frequency is above 400HZ Frequency: 400HZ-20KHZ! When the motor is connected, it can not be directly given high level, and it should not be left floating. Connect the motor for testing. Before testing the drive board, please use an oscilloscope or a multimeter to determine whether the PWM signal you provide is accurate set PWM to 0 when the main program is executed.
This allows the car to start and kill the car quickly. 2. Use a multimeter or oscilloscope to test the waveform between the motors. Determine the pwm signal. Do not connect the motor first, and all other signal power supplies are normal.
Dc motor drive board: 10a dual-channel motor drive board, stepping DC motor with brake H-bridge balance car drive module, DC motor high-current full-bridge drive specially designed for robot competitions. Note: for customers who use arduino stm32 microcontrollers, please note that because these microcontrollers take a long time to initialize, it is necessary to add a 2K pull-down resistor to PWM1 and PWM2 respectively. Test: 1. 3.
ICQUANZX #ad - Power requirement: dC 9-50 V / wide operating voltage range. The maximum current of this regulator is 40A. You can adjust the speed of the motor and the direction of rotation.
Aideepen #ad - Small size, 0 standby current, light weight, is the ideal choice for your car model. Minimal heat, small size, low power consumption, no heat sink, is ideal for battery powered. Use of imported original chip, built-in low on-resistance MOS switch.
RioRand #ad - Adjust the motor smooth no noise no vibration, with power indication, wide duty cycle adjustment range. Potentiometer cable（about 15CM） can be separated, with running stop brake function.
AITRIP #ad - This module can use built-in 78m05 for electric work via a driving power supply part. But to avoid the damage of the voltage stabilizing chip, please use an external 5V logic supply when using more than 12V driving voltage.
Using l298n made by st company as the control chip, the module has such characteristics as strong driving ability, low calorific value and strong anti-interference ability.
HONBAY #ad - L298n has such characteristics as strong driving ability, low calorific value and strong anti-interference ability. This module can use built-in 78m05 for electric work via a driving power supply part.
Using large capacity filter capacitor, this module can follow current to protect diodes, and improve the reliability.
1. Kyuionty
#adKyuionty DC Motor Driver L298 DC 6.5V-27V 7A Dual H Bridge Motor Speed Controller PWM Motor Regulator Board 12V 24V Motor Control Module Industrial with Optocoupler Isolation, 160W
#adForward & reverse rotation: in1, in2/iN3, IN4 ports can control the forward or reverse rotation of the motor. Pwm speed control: enable the signal terminal ENA input PWM to adjust the speed, PWM frequency range 0-10KHZ.
More information #ad
Undervoltage protection: The motor driver module has undervoltage protection to prevent the instantaneous large current from damaging the module. Strong drive: the motor control board adopts double H bridge, which can drive two DC motors at the same time.| Brand | Kyuionty #ad |
| Manufacturer | Kyuionty #ad |
| Part Number | JL0136-1 |
More information #ad
2. uniquegoods
#adUniquegoods Ultra High Power 100A DC Drive Module Motor Speed Controller Dual Channel H-bridge Optocoupler Isolation Easy Control for Robot Chariot Competition Freescale Games
#ad3. 3v and 5v mcu can control this module, and only need the way the motor power 12V ~ 48V. The control interface is very simple: a1. A2 = 00 when the brakes; when a1.
More information #ad
A2 = 1. 0 for forward; A1. A2 = 01 when reversing; pa for pwm wave input motor speed adjustment; G for the Dashboard common ground pin B road for the same control. The basic components of the drive module body placement, onboard two-way high-power DC motor drive, very small, very beautiful, well-designed board layout, highly integrated, the drive module size of only 82mm * 70mm.| Brand | uniquegoods #ad |
| Manufacturer | Meimotor Electronic Technology Co., Ltd. #ad |
| Height | 3.15 Inches |
| Length | 2.76 Inches |
| Width | 0.98 Inches |
| Part Number | UN178 |
More information #ad
3. Ardest
#adArdest L298N Dual H-Bridge Motor Drive Controller for Arduino Smart Car Robot Power Stepper Motor Driver Module
#adWell built dual-channel H-bridge driver working mode creates higher working efficiency. L298n dual motor controller module is a neat motor control module based on the L298N H-bridge IC that can allows you to control the speed and direction of two DC motors, or control one bipolar stepper motor with ease.
More information #ad
L298n as main driver chip makes strong driving ability/small heating/strong anti-interference/low calorific value.| Brand | Ardest #ad |
| Manufacturer | Ardest #ad |
| Height | 26 Millimeters |
| Length | 43 Millimeters |
| Width | 43 Millimeters |
| Part Number | Motor Drive Controller |
More information #ad
4. KNACRO
#adKNACRO Dual DC Motor Drive Module With optocoupler isolation 12V 24V 7A 160W H Bridge for DIY Robot Car
#adMore information #ad
Dual channel dc motor driver board with 7V ~ 24V voltage input supporting undervoltage protection. Sink current drive the control signal, compatible with most MCU board perfect for DIY robot car projects.| Brand | KNACRO #ad |
| Manufacturer | KNACRO #ad |
| Part Number | 7A 160W |
More information #ad
5. Thincol
#adDual DC Motor Driver Module Board, H-Bridge DC 3~36V 10A Peak 30A Speed Control PWM Module, MOSFET IRF3205 Quick Response Control Board for Arduino Robot Smart Car
#adThis allows the car to start and kill the car quickly. 2. Use a multimeter or oscilloscope to test the waveform between the motors. Determine the pwm signal. Do not connect the motor first, and all other signal power supplies are normal.
More information #ad
Pwm modulation: it can work at 0%-99% pwm modulation duty cycle note that it cannot be 100%, so that the motor can get enough driving voltage. N-channel irf3205 mosfet: it can quickly open the moSFET channel, improve the acceleration curvature of the motor, and also quickly brake the motor. Dc motor drive board: 10a dual-channel motor drive board, stepping DC motor with brake H-bridge balance car drive module, DC motor high-current full-bridge drive specially designed for robot competitions. Note: for customers who use arduino stm32 microcontrollers, please note that because these microcontrollers take a long time to initialize, it is necessary to add a 2K pull-down resistor to PWM1 and PWM2 respectively. Test: 1. 3.
| Brand | Thincol #ad |
| Manufacturer | Thincol #ad |
| Height | 0.79 Inches |
| Length | 4.25 Inches |
| Width | 2.28 Inches |
| Part Number | Thincols0frxp5vtu |
| Model | Thincols0frxp5vtu |
More information #ad
6. ICQUANZX
#adICQUANZX DC Motor Controller,DC 9-50V 40A DC Motor Speed Control Reversible PWM Controller 12V 24V 36V 48V 2000W Forward Reverse Switch
#adMore information #ad
Control power: 001-2000w maximum rated current 40A, long operating current up to 20A. Bigger current, high torque,, forward backward direction. Direction control: rocker switch, "i" is forward / CCW and "0" is STOP / CW, "II" is reverse / brake.| Brand | ICQUANZX #ad |
| Manufacturer | ICQUANZX #ad |
More information #ad
7. Aideepen
#adAideepen 5pcs Dual H-Bridge DC Stepper 1.5A 2 Way DC Motor Driver Module Replace Stepper L298N for Arduino Smart Car Power
#adMore information #ad
Dual 1. 5a * 2, built-in thermal protection circuit, do not be afraid motor stall burned, the peak current to be 2.5a, automatic recovery after the temperature dropped. Dual h-bridge motor driver, can drive two DC motors or a 4-wire two-phase stepper motor.| Brand | Aideepen #ad |
| Manufacturer | Aideepen #ad |
| Part Number | 0113395 |
More information #ad
8. RioRand
#adRioRand 7-70V PWM DC Motor Speed Controller Switch 30A
#adMore information #ad
Pwm frequency: 12KHZ. Suitable for long hours of work:Circuit optimization design, stable. Using imported high-voltage MOS tube, three pressure 100V high-frequency low-resistance capacitors, automotive fuses.| Brand | RioRand #ad |
| Manufacturer | RioRand #ad |
| Height | 1.4 Inches |
| Length | 3.4 Inches |
| Width | 2.3 Inches |
| Part Number | RR-MJLK-FBDG |
| Model | 7-70V PWM DC |
More information #ad
9. AITRIP
#ad4Pack L298N Motor Drive Controller Board DC Dual H-Bridge Robot Stepper Motor Control and Drives Module for Arduino Smart Car Power UNO MEGA R3 Mega2560 4 PACK
#adUsing l298n made by st company as the control chip, the module has such characteristics as strong driving ability, low calorific value and strong anti-interference ability.
More information #ad
Using large capacity filter capacitor, this module can follow current to protect diodes, and improve the reliability. To avoid damage the voltage stabilizing chip, please use an external 5V logic supply when using more than 12V driving voltage. Dual-channel H-bridge driver working mode creates higher working efficiency.| Brand | AITRIP #ad |
| Manufacturer | AITRIP #ad |
More information #ad
10. HONBAY
#adHonbay L298N Motor Drive Controller Board DC Dual H-Bridge Robot Stepper Motor Control & Drives Module for Arduino Smart Car Power UNO MEGA R3 Mega2560 Duemilanove Nano Robo
#adUsing large capacity filter capacitor, this module can follow current to protect diodes, and improve the reliability.
More information #ad
Dual-channel H-bridge driver working mode creates higher working efficiency. But to avoid the damage of the voltage stabilizing chip, please use an external 5V logic supply when using more than 12V driving voltage. L298n as main driver chip makes strong driving ability/small heating/strong.| Brand | HONBAY #ad |
| Manufacturer | Honbay #ad |
| Part Number | L298N-1P |
More information #ad
